About us

I am an independent automotive interior pattern and process engineer based in Zhuhai, China, with 16 years of experience. I spent over 10 years in Guangdong developing seat patterns, then 7 years doing full interior wrapping — seats, floor mats, steering wheels, door panels, headliners, A/B/C/D pillars, sun visors, airbag covers, center consoles and dashboards. The last 4–5 years I worked as a new energy vehicle interior wrapping process engineer. I develop car seat cover cutting patterns, 3D floor mat cutting templates and stitched steering wheel wrap patterns for seat cover workshops and custom builders, as an independent pattern developer. All of it is my original, self-owned data, drafted from the original vehicle trim and to the original construction, so each panel follows the real seat frame, pillar structure and floor geometry of the vehicle it belongs to.

That library is the product. Most buyers are seat cover workshops and custom builders who use the pattern as the base for their own seat cover or trim programme: it fits the car as supplied, and because the geometry is correct they can go on to develop their own colourways, two-tone splits, embroidery, badges and panel designs on the same base. Where the library does not cover a vehicle, I develop the pattern to your specification in the same way. This vehicle-specific pattern development service is the route most buyers start with, and it is also how a customer who needs a car seat cover DXF for a model outside the library gets one.

Every pattern here started as a survey. Producing one means sourcing the vehicle, measuring across different platforms and trim levels, accessing or removing the trim, recording what changed between model years, and checking every panel back against the car. Vehicles come from trim specialists, dealer workshops, private owners and customer referrals, so the library reflects what is actually being covered in the market. That work is why the library exists — it has been done once for each vehicle so that buyers do not have to repeat it for every order.

Every delivery is AAMA-standard DXF cutting files with a 1:1 PDF for size checking. Each file marks panel separation, stitch lines, seam allowance, notches and material direction, so it goes straight to cutting without a second round of trial-and-error. The automotive trim cutting files are delivered as one ZIP archive with a piece list and material grain direction written out, so the cutting room works from one document.

10,000+ Original-fit patterns in the library
16 Years of experience
11 Vehicle parts covered
2 File formats per delivery (DXF + PDF)

Patterns are developed per vehicle and per parts group. Please include year, trim and seat configuration in your inquiry so the pattern matches your vehicle.

What we do

Patterns developed for the part, not for a catalogue

Each vehicle panel has its own shape, its own seam layout and its own pull and stretch behaviour. A generic file cannot account for that. Our work starts from your reference part and ends with a file that fits the panel it was drawn for.

I work with upholstery shops and custom car builders. The output is delivered as cutting files with a written specification, so the cutting room works from one document.

  • Developed from your reference

    Photos or measurements of the original trim. The more complete the reference, the closer the first draft lands.

  • Scope confirmed before drafting

    Feasibility and the exact scope are agreed in writing before any pattern work starts.

  • Validated before delivery

    Exported files are checked by overlay against the reference, so geometry errors are caught before they reach the cutting table.

  • Documented on delivery

    Every delivery includes a specification listing each piece, its quantity and its material direction.

  • Clear revision terms

    The number of revision rounds is stated in the quotation. Additional parts or design changes are quoted separately, in advance.

Working method

Six steps from inquiry to delivery

  1. Inquiry and reference

    You send the vehicle year and model, the part you need, the material and your reference photos or measurements.

  2. Scope confirmation

    We confirm feasibility, the pieces to be covered and the delivery time before drafting begins.

  3. Pattern development

    Drafting in CAD, with panel lines, seams, pull and stretch areas checked against the reference part.

  4. Export and validation

    Files are exported to AAMA standard and validated by overlay against the original before they are released.

  5. Nesting

    The DXF is laid out for the material stack agreed with you, so a complete set can be cut in one run.

  6. Delivery and handover

    DXF, PDF and the written specification are delivered as one package directly to you, by email or on request over WhatsApp.

What we need from you

Reference information

Accurate work depends on accurate reference. These are the items that let a pattern be developed without guessing.

  • Vehicle identification

    Year, make, model and trim level where it changes the panel shape.

  • Part identification

    Which seat, mat, wheel or trim panel is to be covered.

  • Reference photos

    Clear photos of the original trim, with a tape measure in frame where possible.

  • Material

    The material you plan to use, and its thickness if known.

Terms

How we work commercially

  • Library first, custom if needed

    Over 10,000 vehicle applications are covered, so the pattern for your car may already exist and can be supplied as it is. Where it does not, the pattern is developed for your specific vehicle after the details are confirmed.

  • Digital delivery

    Pattern files only. No physical samples, finished covers or shipping are included in the standard packages.

  • Your own site, your own contact

    You deal with us directly. Communication runs through email or WhatsApp, payment through Payoneer or bank transfer, and the files are delivered to you — no marketplace sits between us.

  • Scope changes quoted

    If the request changes after the scope is agreed, the new work is quoted before it is started.

  • MOQ 1 pattern

    No minimum order quantity and no minimum order value. Repeat orders for the same vehicle are quoted on the same basis.

  • Fitment guarantee

    If a pattern does not fit the vehicle as confirmed on the proforma invoice, it is corrected at no charge or the deposit is refunded.

  • Aftermarket use

    All patterns are for aftermarket retrofit and restoration use only, and are not OEM original data.

Send us the vehicle and the part

You will get a written scope and a confirmed price before any drafting begins.

Send an inquiry